Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Yamada, Hirokazu*; Kawamura, Hiroshi; Nagao, Yoshiharu; Takada, Fumiki; Kono, Wataru*
Journal of Nuclear Materials, 355(1-3), p.119 - 123, 2006/09
Times Cited Count：5 Percentile：36.24(Materials Science, Multidisciplinary)In this study, the bending properties of welding joint of irradiated material and un-irradiated material (irradiated/un-irradiated joints) were investigated using SS316LN-IG, which is the candidate material for the cooling pipe of ITER. The results of this study showed that the bending position of joints using un-irradiated material was un-irradiated part and that the bending position of irradiated/irradiated joints was fusion area or HAZ (heat affected zone). Although the bending position of joints was different bor the combination pattern between irradiated and un-irradiated materials, the bending strength of joint was almost same. Additionally, it is confirmed that bending strength did not depend on the combination pattern between the irradiated and un-irradiated materials, nor on the relationship between the heat input direction and the bending load direction.
Shibata, Taiju; Sumita, Junya; Baba, Shinichi; Yamaji, Masatoshi*; Ishihara, Masahiro; Iyoku, Tatsuo; Tsuji, Nobumasa*
Key Engineering Materials, 297-300, p.728 - 733, 2005/11
no abstracts in English
Baba, Shinichi; Shibata, Taiju; Yamaji, Masatoshi*; Sumita, Junya; Ishihara, Masahiro; Motohashi, Yoshinobu*; Sawa, Kazuhiro
Nihon Kikai Gakkai Kanto Shibu Ibaraki Koenkai (2004) Koen Rombunshu (No.040-3), p.61 - 62, 2004/09
no abstracts in English
O
joints bonded using superplastic ceramics as interlayerSato, Takashi*; Motohashi, Yoshinobu*; Sakuma, Takaaki*; Waseda, Kazuyoshi*; Shibata, Taiju; Ishihara, Masahiro; Sawa, Kazuhiro
Nihon Kikai Gakkai Kanto Shibu Ibaraki Koenkai (2004) Koen Rombunshu (No.040-3), p.55 - 56, 2004/09
no abstracts in English
Yoshida, Katsuhiko*; Maekawa, Fujio; Takada, Hiroshi
JAERI-Tech 2003-019, 52 Pages, 2003/03
JAERI-Tech-2003-019.pdf:2.89MB
Under the JAERI-KEK High-Intensity Proton Accelerator Project (J-PARC), a spallation neutron source driven by a 3 GeV-1MW proton beam is planed to be constructed as a main part of the Materials and Life Science Facility. Overall dimensions of a biological shield of the neutron source had been determined by evaluation of shielding performance by Monte Carlo calculations. This report describes results of design studies on an optimum dividing scheme in terms of cost and treatment and mechanical strength of shield blocks for the biological shield. As for mechanical strength, it was studied whether the shield blocks would be stable, fall down or move to a horizontal direction in case of an earthquake of seismic intensity of 5.5 (250 Gal) as an abnormal load. For ceiling shielding blocks being supported by both ends of the long blocks, maximum bending moment and an amount of maximum deflection of their center were evaluated.
Ishihara, Masahiro; Kojima, Takao; Hoshiya, Taiji
Proceedings of International Conference on Carbon in 2002 (Carbon2002) (CD-ROM), 6 Pages, 2002/00
Bending failure of two-dimensional C/C composite was studied by both experimental and analytical approaches. In the experiment, a bending test and observation of failure surfaces were performed. From the surface observation, three kinds of fundamental fracture modes were observed; these were tensile, compressive and shear fracture modes. In the analysis, the risk-based statistical fracture theory, so-called the competing risk theory was applied to clarify the bending failure taking account of the competition of these fracture modes. Parameters used in the theory on these fundamental fracture modes were determined by additional experiments, and the theory was applied to the bending failure prediction. As a result of this study, it is concluded that the bending failure was well predicted by the theory, and that the theory would be possible to predict the strength under stress gradient condition. Furthermore, a new strength prediction method combined with FEM code, which is applicable to arbitrary shaped structures with stress gradient, was proposed in this paper.
; ; ;
JAERI-M 84-130, 40 Pages, 1984/07
no abstracts in English
Yumura, Takanori; Amaya, Masaki
no journal, ,
no abstracts in English
